Every Cause and Solution for Roomba Noise Troubleshooting
Roomba vacuum robots are quite useful, but they are not inexpensive. That’s why you should always pay attention when something sounds unusual.
It’s usually enough to clean the Roomba thoroughly or plug it into another charging station or socket while it’s charging to get rid of most of the weird noises.
In this article, we’ll go over some of the most prevalent issues and how to get rid of the noises they cause. In addition, all Roomba models’ beeping trouble codes are mentioned at the end.
During the charging process, there is a ticking noise.
When charging, customers frequently remark that their Roomba emits weird ticking noises. This problem occurs rather frequently, but it is extremely simple to fix. The first thing you should do is plug the charging station into a different outlet. If the noise persists, Roomba Tech Support will propose slightly pushing the dirt container out of the way during the loading procedure.
This noise can also emanate from the loudspeaker on some models. Although this is a rare occurrence, it can be readily remedied by turning off the loudspeaker. If the ticking noise continues when charging, your charger may be defective.
Find the proper charger for your Roomba here. You can also read about how to clean heavily soiled carpet!
Noises While Your Roomba Is Running
If your Roomba makes strange noises when cleaning, it’s usually because something is mechanically stuck or twisted.
To turn this off, you must clean your Roomba thoroughly of dirt and foreign objects. Your vacuum robot will be as clean as it was at the start if you clean the following components, thus there should be no unpleasant noises:
- The brushes
- The extractors
- The cleaning head
- The vacuum impeller
You can test which of these parts is causing the noise by removing them one at a time and running the Roomba without them. If you remove the extractors and the noises go away, the extractors are the source of the problem. If you are facing roomba not charging problem.
How to Clean the Brushes in a Roomba?
When the built-in Roomba brushes are unable to rotate properly, thumping or clicking noises are common.
These brushes mimic standard vacuum cleaner brushes with bristles for Roomba machines up to the 600 series*. The brushes of the 800 series* are made of rubber with a unique design.
These brushes, regardless of the model you have, can become clogged with debris, dirt, or hair and stop rotating properly. As a result, an unusual noise is produced. To clean the brushes, follow the steps below:
- Remove the housing plate of the brush.
- Remove the brush from the Roomba.
- Also remove the suspension of the brush.
- Now clean the inside of the Roomba and the dismantled parts.
- Reassemble the Roomba.
How to Clean the Extractors in a Roomba?
Cleaning the extractor rollers and brushes on a Roomba are fairly similar. It shouldn’t take more than a few minutes to complete the procedure. The following are the measures to clear the extractors in a Roomba of any things that could cause a noise:
- Open the Roomba.
- Remove the extractors and remove the suspension pieces at both ends.
- Remove all dirt and hair that you can find.
- Put everything back together like it was before.
Cleaning the Roomba brushes or extractors is usually enough to get rid of unpleasant noises. Make sure you clean thoroughly because the debris that generates the noises can sometimes sit deep and be difficult to reach.
Extractors that have been installed incorrectly are making clicking noises.
Extractors that are not properly positioned in the cleaning head might also produce clicking noises. You can simply check this by uninstalling and reinstalling the extractors. The majority of the time, you can see the error right away. More information is available on iRobot’s official website.
Noises After Replacing the Extractors
When you replace the extractors on a Roomba 800 series or higher, you’ll run into another unique issue.Then it’s possible that the new extractors are a bit too large in diameter and rub against each other. This isn’t as unpleasant at first, and it will go away on its own as they rub against one other, removing the irritating places on their own.
How to Clean the Cleaning Head of a Roomba?
If the noise isn’t coming from the brushes or extractors, you could try removing, cleaning, and reassembling the entire cleaning head.
You could simply purchase a new cleaning head*, but if you have some technical knowledge and patience, you can clean and repair the head yourself.
The gears in your Roomba’s gearbox will get progressively stiff or even totally clogged if hair or other dirt accumulates in the gearbox.
The procedure is the identical for all Roombas in theory. The actions outlined below, however, are applicable to all Roombas up to the 600 series. An official iRobot video is provided at the conclusion of this section for newer models.
The cleaning head has numerous gears and other moving parts that can be clogged by dirt and, in particular, hair. This means that not only does your Roomba have to work harder during cleaning, putting a strain on the battery, but it also results in annoying noises. The cleaning head disassembly is time-consuming, especially when compared to cleaning the brushes.
Last word about this Article
Cleaning a Roomba thoroughly can eliminate the majority of the noises it generates over its lifespan.
Hair, lint, or dirt inside the housing are the most prevalent causes of unpleasant noises. Cleaning the brushes, extractors, or even the entire cleaning head can eliminate 90% of the noise. In some circumstances, the motor and vacuum impeller may also need to be removed and cleaned.
The charging procedure, in addition to these mechanical noise sources, may be to blame. Simply change the power outlet, remove the Roombas’ dirt container while charging, or turn off the speakers to find out.
I hope this post has helped you find a solution to your problem so you can continue to enjoy your autonomous vacuum robot! Visit Ofarticle to know more