The remedy might be as simple as changing the outlet or cleaning the charging contacts, depending on the Roomba’s age. It may also necessitate a more significant repair, such as the replacement of some parts or the purchase of a new Roomba. Below, we’ve gone through the issues in how to fix roomba not charging!

How to fix roomba not charging on dock!

If you are facing this problem and want to get rid from this problem, then follow these step. You will be able to do it easily

Reset the Device

After you’ve confirmed that the outlet is operational, you’ll need to factory reset the device. It’s possible that the device’s failure to keep a charge is due to a glitch or a software fault. You should be able to solve it with a hard reset. The method for doing so on your Roomba device will vary depending on the model. You may reset your Wi-Fi-enabled models directly from the app. To reset the device, follow the instructions and models found here.

• s Series/i Series: Press the Home+Spot Clean+CLEAN buttons at the same time until the CLEAN button light flashes.
• Press the Home+Spot Clean+CLEAN buttons at the same time for 20 seconds on the e Series Roomba.
• 900 Series Roomba: Hold down the Dock+Spot Clean+CLEAN buttons at the same time until all of the LEDs light up.
• Robots in the 600 and 800 Series with Wi-Fi: Press the Dock+Spot Clean+CLEAN buttons at the same time until you hear a beep.
• Roomba Combo: The reset button is located next to the power button under the lid. For at least 10 seconds, press and hold the Reset button.

You should double-check the reset technique in your user’s manuals if you’re using the most recent models of these models.

Cleaning the Charging Contacts

The Roomba can gather up a lot of dirt and debris while it’s running, especially if you’re using it on a very filthy floor. Because these devices are meant to be low to the ground, debris may enter the device while it cleans. For charging at their base, the Roomba’s charging contact is at the bottom. Electricity will not be able to pass through if this becomes dirty or clogged with trash. The charging base will become dirty over time and will need to be cleaned on a regular basis to keep the Roomba powered.

Read Also: how to clean berber carpet?

While most Roombas are marketed as completely hands-free devices, they still require a few touches and routine maintenance, similar to a vacuum cleaner. If the Roomba won’t charge, wipe the charging contacts (with anything other than a damp cloth) and attempt charging again. This should fix the problem, but if it doesn’t, you’ll have to take the vacuum to a local repair shop to have it looked at for hardware issues.

Replaced the Battery

Take note of the Roomba’s performance before assuming it won’t charge while plugged in. Is the Roomba only partially charged or is it draining too quickly? If the Roomba isn’t working as well as it used to, even after cleaning the charging contacts, resetting the Roomba, or changing the outlet, you may need to replace the battery.

If you have an older Roomba, the remedies above may not work because the lithium-ion battery can last for many cycles but eventually loses its ability to retain a charge. Continuous use will deplete the battery life, especially if you use the gadget frequently.

Instead of replacing the battery, you could upgrade to a newer model with more features. Nonetheless, your choice will be influenced by your financial constraints. A good battery will be far less expensive than a new vacuum cleaner.

Fix the Battery Position

If you frequently move your Roomba from one location to another, there’s a good possibility you’ve run it into something. If this is the case, the batteries may have been shifted from their original position as a result of the occurrence. This isn’t a typical event, but if you’re not careful, it may happen to you. It is also worthwhile to investigate.

Open the 5 screws on the Roomba’s base to try to fix the battery position. Open the battery compartment and double-check that the batteries are in position. Replace the screws and connect the Roomba.

Before you do anything, double-check your warranty to determine if opening the vacuum will void it. If that’s the case, you might want to hire an expert to assist you. You should try the other remedies first, and if you find that the batteries are in the correct place, the Roomba can be repaired from there.

Claim Warranty

first try to claim your Roomba warranty before taking it to a professional for repair. You could contact customer service if the item is still under warranty and look through the community forums to see if somebody has already solved the problem in another way.

If not, the best option is to file a warranty claim. You may receive a replacement or be required to send it in to be repaired by the company. You may not have to pay more in some situations, but this will depend on how long you’ve been using the gadget.

Final Thoughts

You can get your Roomba to start charging again with these fixes. Checking the outlet, restarting the device, and cleaning the charging base are all good places to start. If none of these solutions work, you may need to consider a battery replacement or a complete replacement. It’s also a good idea to see if your warranty is still valid. Visit our site for more.